Restore-A-Deck Wood Stain Stripper

$34.99
free shipping with ground services
#1 Rated Wood and Deck Stain Stripper that removes clear, transparent, semi-transparent, and most semi-solid coatings.

Extremely cost-effective. When mixed, the cost is less than $7 a gallon.
 Back to: Restore-A-Deck Prepping Products

info button

Restore-A-Deck Wood Stain Stripper Official Dealer

Makes 5 Liquid Gallons ...Enough to Strip 500-1000+ Sq. Feet!

Restore-A-Deck Wood Stain Stripper: the Best Deck Stain Stripper

Restore-A-Deck Wood Stain Stripper is a biodegradable, powdered concentrate that quickly removes worn finishes to restore wood surfaces. Stains and varnishes are removed along with collected dirt, mold, mildew and mill glaze.

The Restore A Deck system is a multistep deck cleaning system, and best results are achieved when using all 3 products. This product is Step 1 Stripper of the Restore A Deck system and can be substituted for or used after Restore-A-Deck Wood Cleaner.

WHERE TO USE
Restore-A-Deck Wood Stain Stripper removes most oil and latex based finishes including: clear sealers, transparent stains, and semi-transparent stains.

SURFACE PREPARATION:
Surfaces to be stripped must be above 50°F. Protect adjacent surfaces; cover with plastic sheets and/or tape off any adjacent areas not being stripped. Thoroughly wet and/or cover plants and shrubs. Rinsing residue will not harm plants or roots. Exposure to full strength product will burn foliage.

The Restore-A-Deck Wood and Deck Stain Stripper needs to be neutralized with the Step 2 Wood Brightener.

ADVANTAGES

  • #1 Rated Wood Deck Stain Stripper
  • Removes most clear, transparent, semi-transparent, and semi-solid coatings.
  • Powdered formula makes 5 liquid gallons when mixed
  • Extremely cost effective. When mixed, the cost is less than $7 a gallon.
  • Eco-Safe formulas
  • Preps previously stained wood and decks
  • Safe to use on all exterior wood surfaces, not just decks
  • Applied with pump sprayer for max results or injected through pressure washer for easier to remove finishes
  • Can be mixed at a stronger ratio for difficult to remove finishes. Max would be 3 gallons of water to one container of Restore-A-Deck Stripper

Coverage: 500-1000 sq.feet per container.

*Will not remove excessively over applied stains, solid color stains, paints, or polyurethanes.

Available Sizes:
2 lb Container
Powder Concentrate:
1 Container Makes 5 Liquid Gallons
Purpose:
Stain Stripper
Coverage Per Gallon:

100-200 sq. ft Per Gallon

Application Tools:
Injector, Sprayer, Stiff Brush
Neutralize: Yes
RAD Step 2

 

 

 

 

Reviews

Sunday, 24 December 2017

#1 Rated Wood and Deck Stain Stripper that removes clear, transparent, semi-transparent, and most semi-solid coatings.

Scott
Ask a Question or Post a Picture...
You are guest ( Sign Up ? )
or post as a guest
Loading comment... The comment will be refreshed after 00:00.
  • We will reply to your comment shortly
    DL · 08/18/2012
    Our deck has been stained twice in 3 years. First time when we put it up and then last time 1 year ago, using Behr. After the winter, with the dogs running in and out, most of the deck stain flaked off. The wood is practically barren in most open areas. Water does not bead up in 80% of the deck surface. There are strips of stain left on the stairs and it is more complete in sections under our overhang. But hubby is thinking it would be fine NOT using a stripper...what do you think? What if we did not use it?
  • We will reply to your comment shortly
    RAD Products · 08/11/2012
    I would mix the 2# container of the RAD stripper with 5 gallons of water. Inject on with you chemical injector. You will get close to 1000 sq. feet of coverage with the 5 gallon pail quite easily but it does depend on the brand on stain you are trying to remove. Some brands are difficult to remove and you should use a pump sprayer instead.
  • We will reply to your comment shortly
    Donna · 08/11/2012
    I am trying to determine application concentration with a pressure washer. We are working vertically and overhead on the porch and need to be up and down a ladder with all 4 sides of posts to be done. On testing with the chemical injector, I use 2 cups of "chemical" to spray a gallon of water which happens in about 30 seconds. At that rate, I will use up 5 gallons in 20 minutes which seems very fast and a huge amount of stripper. Directions say it will do 500-1000 s.f. but the math doesn't seem to add up. There is no adjustment on the rate of spray. Also, I am diluting the solution by a 1:8 ratio. Will it still be effective?
  • We will reply to your comment shortly
    RAD Products · 08/10/2012
    You can inject the RAD stripper with a downstream injector and a soap tip. Saturate the wood well and let sit for 10-15 minutes. Pressure was off.
  • We will reply to your comment shortly
    Donna · 08/10/2012
    I am applying RAD Stripper with a Craftsman pressure washer. Do I use the soap/detergent hose and nozzle? Any special dierections?
  • We will reply to your comment shortly
    RAD Products · 08/06/2012
    The RAD Stripper will remove most of it but Behr can be stubborn. If you cannot get it all off then I would suggest the Armstrong Clark in one of the semi-solid colors.
  • We will reply to your comment shortly
    chris · 08/05/2012
    Hello - we are prepping an older pressure treated deck for staining. The old stain appears to be semi-trans (color is uniform, but can see grain). The old stain is likely Behr brand. We've replaced a few boards with the current flavor of pressure treated wood (home depot). The new boards haven't been stained.

    Two questions:
    Is the RAD stripper the best choice for this scenario? If we go with the RAD stripper and it doesn't get off all the old finish (and we don't want to sand due to the toxic wood), should we stick with semi-trans, or go with a solid color stain?

    Thanks
  • We will reply to your comment shortly
    RAD Products · 08/03/2012
    In some cases the stripper may raise the grain slightly. If it does then you can lightly sand with 60 grit after using the stripper and brightener.
  • We will reply to your comment shortly
    Bill · 08/03/2012
    Do I need to sand the deck if I use RAD? My plan of attack, because a semi transparent stain was put on, is to use the stripper then the brightener and skip the cleaner then seal.
  • We will reply to your comment shortly
    RAD Products · 07/31/2012
    Behr can be very difficult to remove. I would strip off as much as possible then sand off the rest if needed.
  • We will reply to your comment shortly
    MARK VERMEER · 07/30/2012
    I've unfortunately used Home Depot water-based (Bear) products to "cedar" stain my deck. Now it is a hodgepodge of open, split cedar wood, some of it fairly bare...but split and some of it with splotches of it Baer stain...and split. I have a big deck, lots of spindles, and lots of stairs. I'm going to try restore-a-deck stripper and brightener. Assuming it works, then what? Assuming it doesn't work, then what?
  • We will reply to your comment shortly
    RAD Products · 07/24/2012
    It should not but best to test a spot first or tarp the windows.
  • We will reply to your comment shortly
    RAD Products · 07/24/2012
    No this will not strip a solid stain effectively.
  • We will reply to your comment shortly
    Harold Hansen · 07/24/2012
    I am stripping oil based semi transparent olympic stain off of ceder siding. Will this product harm bronze anodizied finish on allumminum window frames.
  • We will reply to your comment shortly
    Liz · 07/24/2012
    I need to strip a solid stain. Will this product work??
  • We will reply to your comment shortly
    RAD Products · 07/08/2012
    Most likely.
  • We will reply to your comment shortly
    Crystal · 07/08/2012
    Would pump sprayer be best choice for RAD stripper on lousy, unknown brand stain on deck?
  • We will reply to your comment shortly
    RAD Products · 06/14/2012
    Yes. You do not need a cleaner if you use the stripper.
  • We will reply to your comment shortly
    Matt · 06/14/2012
    Hi,
    Does the RAD stripper eliminate the need to use the RAD cleaner?