Restore-A-Deck Wood Stain Stripper Booster
Restore-A-Deck Wood Stain Stripper Booster
Restore-A-Deck Wood Stain Stripper Instructions

Restore-A-Deck Wood Stain Stripper

2 Ratings 1 Shopper Review
$39.99
free shipping with ground services
#1 Rated Wood and Deck Stain Stripper that removes clear, transparent, semi-transparent, and most semi-solid coatings.

Extremely cost-effective. When mixed, the cost is less than $8 a gallon.
 Back to: Restore-A-Deck Prepping Products

info button

Restore-A-Deck Wood Stain Stripper Official Dealer

Makes 5 Liquid Gallons ...Enough to Strip 500-1000+ Sq. Feet!

Restore-A-Deck Wood Stain Stripper: the Best Deck Stain Stripper

Restore-A-Deck Wood Stain Stripper is a biodegradable, powdered concentrate that quickly removes worn finishes to restore wood surfaces. Stains and varnishes are removed along with collected dirt, mold, mildew and mill glaze.

The Restore A Deck system is a multistep deck cleaning system, and best results are achieved when using all 3 products. This product is Step 1 Stripper of the Restore A Deck system and can be substituted for or used after Restore-A-Deck Wood Cleaner.

WHERE TO USE
Restore-A-Deck Wood Stain Stripper removes most oil and latex based finishes including: clear sealers, transparent stains, and semi-transparent stains.

SURFACE PREPARATION:
Surfaces to be stripped must be above 50°F. Protect adjacent surfaces; cover with plastic sheets and/or tape off any adjacent areas not being stripped. Thoroughly wet and/or cover plants and shrubs. Rinsing residue will not harm plants or roots. Exposure to full strength product will burn foliage.

The Restore-A-Deck Wood and Deck Stain Stripper needs to be neutralized with the Step 2 Wood Brightener.

ADVANTAGES

  • #1 Rated Wood Deck Stain Stripper
  • Removes most clear, transparent, semi-transparent, and semi-solid coatings.
  • Powdered formula makes 5 liquid gallons when mixed
  • Extremely cost effective. When mixed, the cost is less than $7 a gallon.
  • Eco-Safe formulas
  • Preps previously stained wood and decks
  • Safe to use on all exterior wood surfaces, not just decks
  • Applied with pump sprayer for max results or injected through pressure washer for easier to remove finishes
  • Can be mixed at a stronger ratio for difficult to remove finishes. Max would be 3 gallons of water to one container of Restore-A-Deck Stripper

Coverage: 500-1000 sq. feet per container.

*Will not remove excessively over applied stains, solid color stains, paints, or polyurethanes fully.

Do you Have a Difficult to Remove Coating?

Restore-A-Deck Stain Stripper Additives

Restore-Deck Stain Stripper Application Tips

How do I strip the sealer from my deck?

Strip or Clean the Deck

Available Sizes:
2 lb Container
Powder Concentrate:
1 Container Makes 5 Liquid Gallons
Purpose:
Stain Stripper
Coverage Per Gallon:

100-200 sq. ft Per Gallon
Application Tools:
Injector, Sprayer, Stiff Brush
Neutralize: Yes
RAD Step 2

 

 

 

 

Reviews

Sunday, 24 December 2017

#1 Rated Wood and Deck Stain Stripper that removes clear, transparent, semi-transparent, and most semi-solid coatings.

Scott

Please log in to write a review. Log in

Related
Restore-A-Deck Wood BrightenerRestore_A_Deck_B_4cd1f6372aaed.gif

Restore-A-Deck Wood Stain Stripper BoosterRestore_A_Deck_I_4f43b5a24adf9.gif

Restore-A-Deck Wood Stain Thickening Gel BoosterRestore_A_Deck_I_4f43b5a24adf9.gif

chapin_clean___s_492acd1318dd6

Restore-A-Deck Wood Stain 1 GallonRestore-A-Deck Wood Stain 1 Gallon

Restore-A-Deck Wood Stain 5 GallonsRestore-A-Deck Wood Stain 5 Gallons

Ask a Question or Post a Picture...
You are guest ( Sign Up ? )
or post as a guest
Loading comment... The comment will be refreshed after 00:00.
  • We will reply to your comment shortly
    Randy · 04/22/2019
    Late last year I used Ready Seal (cedar color) to stain our screened-in porch. Porch was built over 35 years ago with cedar with redwood support columns and beams. Do I use your stripper or cleaner product before brightening and staining?

    Secondly, should I use a brush to apply the stripper or cleaner as recommended above so product does not affect outside painted surfaces?
    • We will reply to your comment shortly
      RAD Products · 04/22/2019
      Yes, strip and brighten. Prep products do not remove paint.
  • We will reply to your comment shortly
    john Kay · 04/16/2019
    If I have very light spots and dark spots. Should I used stripper then brightener, or cleaner then brightener?
    • We will reply to your comment shortly
      RAD Products · 04/16/2019
      Best to post a picture here so we can see the best way to prep.
  • We will reply to your comment shortly
    Lori · 04/15/2019
    Hi. We just used a different stripper on our IPE deck and there are still areas that have quite a bit of stain left. Those areas were not exposed to the sun, so the stain was still mostly in tact. Looking to purchase RAD stripper and brightener for the next round. Do you have any tips or recommendations for removing stain from IPE? Is it helpful to use a brush when applying the stripper? Was thinking about possibly sanding, but not sure you're supposed to sand IPE. Not sure what stain the contractors used a few years ago, but it's a mahogany color. Thanks in advance for your help!!!
    • We will reply to your comment shortly
      RAD Products · 04/15/2019
      Post a picture on the stain that is still on the IPE.
      • We will reply to your comment shortly
        Lori · 04/15/2019
        Thanks for the quick reply. Here are some pics.
        • We will reply to your comment shortly
          RAD Products · 04/15/2019
          The old contractors used the wrong type of stain in this. this coating created a film on top of the wood similar to a varnish, that is why you are having a hard time stripping it off. Stain strippers will have difficulty removing this. You can try the RAD Stripper with the Boost and Gel: https://www.restore-a-deck.com/rad-stain-stripper-additives.html

          but there is no guarantee it will come off fully. Apply, let dwell for 30 minutes or longer by misting to keep it wet, then pressure wash off.
          • We will reply to your comment shortly
            Lori · 04/15/2019
            Okay. Would it help to brush in at all while applying? If the stain does not come off, can IPE be sanded? Thank you for the advice!
            • We will reply to your comment shortly
              Rynae · 05/10/2019
              Lori, let me know how your stripping goes. I had a fence company stain our Ipe and they used Miniwax Wood Finish and it looks terrible. We haven't tackled our project yet, but would be interested in seeing what worked for you. I'm getting ready to order the stripper/brightener but it sounds like I might also need the boost and gel. Thanks!
            • We will reply to your comment shortly
              RAD Products · 04/15/2019
              You can scrub/agitate the stripper after about 15 minutes, reapply the stripper again, and then pressure wash off.
  • We will reply to your comment shortly
    Alex · 02/26/2019
    is scrubbing necessary if power washing? Looking to remove TWP 1500 from the deck
    • We will reply to your comment shortly
      RAD Products · 02/26/2019
      No need to scrub if pressure washing.
  • We will reply to your comment shortly
    Alex · 02/12/2019
    I plan on stripping the deck floor, TWP on there now, I have a solid stain on the railings, do I need to worry about getting stripper on them and affecting the solid stain?
    • We will reply to your comment shortly
      RAD Products · 02/13/2019
      The stripper does not remove solid stain unless the sold stain is peeling already.
  • We will reply to your comment shortly
    Alex · 02/12/2019
    What angle nozzle do you recommend on the power washer? I figured out the right size for 800 psi but wondering what angle to use, 25 degrees?
  • We will reply to your comment shortly
    Tango · 10/10/2018
    If I strip and brighten now, can I wait until Spring to stain? It's just the stain that is on there seems to promote mold . . . and with the weather changing, I may not can stain now . . . . Or should I just wait until Spring? Thank you!
    • We will reply to your comment shortly
      RAD Products · 10/10/2018
      If you strip/brighten now, you will need to redo in the Spring with a cleaner and brightener.
      • We will reply to your comment shortly
        Tango · 10/10/2018
        Thank you!
  • We will reply to your comment shortly
    Tango · 10/08/2018
    I plan on using this product in the spring. I have a year old deck stained with SW Superdeck. Have had lots of mold and mildew due to rain, humidity and aphid droppings from the trees. Have power washed x2 in a month and have power washed some of the stain off since I knew I would be stripping it anyway. When I get ready to start this project, can I skip the cleaning and just start with the stripping step? It's a treated yellow pine deck.
    • We will reply to your comment shortly
      RAD Products · 10/08/2018
      You do not need a cleaner if using the stripper. Apply stripper and pressure wash off. Rinse and apply the brightener. Rinse that well after about 15 minutes.
      • We will reply to your comment shortly
        Tango · 10/08/2018
        Great to know! Thank you very much!!!
  • We will reply to your comment shortly
    Peter Jacobson · 09/21/2018
    Have 1000 ft2 22-year old PT deck. Was RAD prepped and stained with Armstrong Clark semi transparent dark brown stain in 2015. Couldn't retreat with RAD 1 and 2 plus same stain as shady end of deck was heavy with green mold and mildew.

    So, decided to strip, brighten and stain all with RAD (light walnut). Have stripped all and brightened just a couple hundred ft2. Periodic rain is going to delay staining a bit. Wood is still fairly wet, which acounts for some of the darkness variation iin pics.

    Have seen references to "furring" in your replies. Is this what pictures of the more open grain are showing and should I sand those boards with 60-80 grit? Would that be sand, rinse and brighten? Also, would light use of an orbital sander be OK or should I stick with a sanding block?

    IF you can reply quickly I'd be very greateful.

    Many thanks,
    Peter
    • We will reply to your comment shortly
      RAD Products · 09/22/2018
      Sand rinse and brighten. 60-80 grit. Floor buffers work the best. I would not suggest an orbital hand sander.
  • We will reply to your comment shortly
    Anthony Ojeda · 09/16/2018
    I live in Georgia and saw the reviews online for your products.

    I used Thompsons Timber Oil in Teak about 2 years ago on new wood and want to strip, clean and re-stain. Will your product bring back the natural wood color? Thanks
    • We will reply to your comment shortly
      RAD Products · 09/16/2018
      Could you please a picture of the current condition.
      • We will reply to your comment shortly
        Anthony O · 09/17/2018
        Sent under 3 emails from phone.
        • We will reply to your comment shortly
          RAD Products · 09/17/2018
          The stripper should remove the stain but you will need to use a pressure washer after applying it and you may need to strip the verticals a couple of times to remove. Brighten after the stripper.
  • We will reply to your comment shortly
    Katie C. · 09/04/2018
    Do I have to follow with the brightener if the wood is fairly new, or will water neutralize it?
    Thanks!
    • We will reply to your comment shortly
      RAD Products · 09/04/2018
      Yes, you have to neutralize with the brightener.
      • We will reply to your comment shortly
        Katie C. · 09/04/2018
        Yikes! OK, so I stripped yesterday, but don't have the brightener. Will it destroy the wood if I don't neutralize? Is there some other neutralizer I can use that I can purchase locally (I'm assuming your brightener won't get here fast enough)? Or is it OK to wait a week or so?
        • We will reply to your comment shortly
          RAD Products · 09/04/2018
          Best to neutralize as soon as possible the same day as stripping to lessen the chance of "furring" but since it has already dried, it will not matter if it waits a week. Our brand will work the best for this.
  • We will reply to your comment shortly
    K.K. · 08/16/2018
    After I applied the stripper and brightener to my deck and power-washed, a lot of the blown off old stain got stuck to the walls. I power-washed the walls but brownish marks are left behind. These marks are like the sticky substance left behind by scotch tapes. How do I get rid of them? They are noticeable and ugly looking.
    • We will reply to your comment shortly
      RAD Products · 08/16/2018
      Try a water-based graffiti remover cleaner from your local hardware store.
  • We will reply to your comment shortly
    Dustin · 08/15/2018
    I have a huge tigerwood deck. It has crd sikkens stain on it. I have got everything off the railings with is stripper. I am having some trouble getting the stain off the floor. There are someboards where it is not coming completely out and when I scrub more it causes some maeks. see the picture. Will these mark show up when stain with restore a deck natural? Should I leave the stain that will not come off? I dont want to damage the boards. Or should I just sand the floor?
    • We will reply to your comment shortly
      RAD Products · 08/15/2018
      Are you pressure washing after applying the stripper? Make sure that you brighten the wood after all the stripping is done.

      Try to remove as much as possible. It seems that most is removed in the picture. The brightener should help as well to even out the appearance some.
      • We will reply to your comment shortly
        Dustin · 08/15/2018
        I am power washing and brightening while it is still wet. It is different boards which the stain remains. The stain will just not come off these particular boards even with scrubbing. I will send a picture of the board.
        • We will reply to your comment shortly
          Dustin · 08/15/2018
          Photo
        • We will reply to your comment shortly
          Dustin · 08/15/2018
          Here are the photos. It tends to be the weaker boards thathat it wont come out of. That is why I am wondering if I should sand the floor instead because I dont want to damage the boards.
          • We will reply to your comment shortly
            RAD Products · 08/16/2018
            You could try the sanding.
            • We will reply to your comment shortly
              Dustin · 08/16/2018
              What level of grit would you reccomend since most of the floor is stripped? Sand, vacuum, wash, brighten and then stain and in that order? I may just stain the floor this year since most is removed and sand the floor next year if I have issues with uneven fading as the railings have been completely stripped and those should not need to be sanded.
              • We will reply to your comment shortly
                RAD Products · 08/16/2018
                60-80 grit paper. Sand, lightly wash and then brighten for the final prep.
  • We will reply to your comment shortly
    john · 08/02/2018
    Hi, RAD.
    Couple question about using this on wood fence.
    First, May I use it on to wood fence?
    Second, fence is vertical stand so I think it will be flow down when I spray on.
    Does it still work as this condition?

    • We will reply to your comment shortly
      RAD Products · 08/02/2018
      Yes, it can be used on a fence. Apply and back wipe tight away to make sure you catch any drips and to make sure it is applied evenly
  • We will reply to your comment shortly
    Brad · 07/26/2018
    Three month follow up. I was very skeptical using a water based stain. My friend, an executive from SW, was talking trash about doing so. I’ve been using TWP, and the cedar tone turns blackish every year. Plus it’s a pain to apply, and you need 3 dry days in a row.

    I stripped my deck and posted the finished photo in April. I’m posting it again today.

    Here’s my April work timeline. I pulled the pressure washer out of the shed at 10 am. Stripped and neutralized twice each to get to bare wood. Was a warm day, southerly exposure. I let the deck dry 90 minutes. Then stained it. Walked on the deck at 3PM same day.

    Full southern exposure, deck take a heat beating. Still looks like identical to April application. Rained all night so I’m posting the water bead up at 4 months! I’ll follow up April 2019.

    Move over oil stain, there’s a new sherif in town!
  • We will reply to your comment shortly
    Gregg Juster · 07/26/2018
    I tested your stripper and brightener on a very small part of my log cabin - however, the person I hired to do the job fell off a ladder and won't be able to start until mid September. Do I need to stain that small are or is it OK to get wet for several months then be stained
    • We will reply to your comment shortly
      RAD Products · 07/26/2018
      You will be fine to leave as is until the Fall.
  • We will reply to your comment shortly
    Pamela · 07/25/2018
    We just paid $$$ to have our large deck stained with SW Superdeck semi-solid Charwood. It is beyond horrible. Way to dark, uneven, sprayer and roller marks and blotches/missed spots everywhere. Will this take it back to where it can be restrained with a different product? Or will anything help?
    • We will reply to your comment shortly
      RAD Products · 07/25/2018
      You sure it is semi-solid and not semi-transparent? Please post a picture of the deck and the can of stain.
  • We will reply to your comment shortly
    leta sellers · 07/20/2018
    what are the ingredients in this product?
  • We will reply to your comment shortly
    Andy · 07/19/2018
    I plan to use Restore A Deck stripper and brightener before staining the following week. Can I strip and brighten if it will rain later in the day? If so how long do I need to allow before rain is expected?
  • We will reply to your comment shortly
    Tom · 07/10/2018
    Will the stain stripper affect the paint on the side of my house? Will I have to cover up the walls next to my deck when applying the stripper?
    • We will reply to your comment shortly
      RAD Products · 07/10/2018
      It will not strip paint unless the paint is already peeling.
  • We will reply to your comment shortly
    Terry · 07/08/2018
    I have metal spindles on my deck railing but the columns and frame are wood. Is this corrosive to the metal?
    • We will reply to your comment shortly
      RAD Products · 07/08/2018
      Depends on the type/brand of spindles you have and if coated or not. Usually not an issue, but best to test first.
      • We will reply to your comment shortly
        Terry · 07/09/2018
        Thanks for the quick response. What would the proper way to test it entail? Just dab some on an inconspicuous spot and see what happens? I have some left over from a project last year.
  • We will reply to your comment shortly
    Carolyn P · 06/30/2018
    Another question. For a 25 year old-ish deck that's been stained....after we get it stripped and perhaps sanded...do we have to stain it? Is there a way to keep it looking nice with just a yearly spray of brightener or something? Some power-washing? This whole thing of sanding a 450 sq. foot deck and lots of railings is making my head hurt!
    • We will reply to your comment shortly
      RAD Products · 07/01/2018
      It will need to be stained to keep it looking good.
      • We will reply to your comment shortly
        Carolyn P · 07/01/2018
        Do we have to go through all the sanding if we do the same stain every 2 years? Can we just power wash and/or clean?
        • We will reply to your comment shortly
          RAD Products · 07/02/2018
          If using one of our brands, then you can just clean and reapply as needed.
  • We will reply to your comment shortly
    Carolyn P · 06/30/2018
    I power washed the deck yesterday and it had 6 year old Behr solid deck stain on it (it peeled and looked awful after a year, but we're finally getting around to doing our deck again). My husband said to use a stripper first, then a belt sander (we'd have to buy), then brightener. Is that the right order? Even more important, can we skip the sanding? Will your stripper take it all off? We have 450 sq feet of deck, plus railings (OMG the sanding of that! yikes!). I've attached photos of some of the slabs of deck and what it looks like after power washing.
    • We will reply to your comment shortly
      RAD Products · 07/01/2018
      A stain stripper will not remove a solid stain fully. It will remove some but you will have to power sand to get it fully removed.
      • We will reply to your comment shortly
        Josh · 04/14/2019
        For this type of situation, would it be better to just sand off the stain first, then use the cleaner and brightener? Or use the stripper, then sand, then brightener? My deck looks similar to these pictures, but I'm not sure what type of stain the prior owners used or how long ago it was applied.
  • We will reply to your comment shortly
    Frank · 06/17/2018
    Olympic Max Deep clean only absorbed into my 15 year old deck - see photo. It had semi transparent grey stain at one point. How/which of your prep products should I use?
    • We will reply to your comment shortly
      RAD Products · 06/17/2018
      Use the RAD Stripper with pressure washing and then the brightener.
  • We will reply to your comment shortly
    Neil Grant · 06/17/2018
    Hi there


    I've just used the Behr deck stripper product and it really didn't touch the Behr paint on my deck, even after two coatings. Your product looks as though it is much more effective, but I have two young children and I can't see what the active ingredients are. I'm trying to avoid products that contain methylene chloride and n-methyl-pyrrolidone (I think these are the ones Lowes is phasing out). Can you confirm that these aren't active ingredients?


    Many thanks


    Neil
    • We will reply to your comment shortly
      RAD Products · 06/17/2018
      Hello,

      A deck stain stripper will not remove a solid color "paint". Not possible and we do state this in our description.
  • We will reply to your comment shortly
    Jonathan Wilson · 06/14/2018
    We applied Cabot Semi Solid Stain to deck 4 years ago.Big mistake as it began to come off immediately on horizontal surfaces (it's fine on vertical).

    Will your stain remover work on getting this product off before we use a Semi Transparent stain next time? I just tried hand sanding a small area and the stain comes off quite easily.
  • We will reply to your comment shortly
    Ken S · 06/08/2018
    Will this remove Wolman Raincoat Tinted (Natural Cedar) Water Repellant Finish (Water Base)?
  • We will reply to your comment shortly
    Alan Ulbrich · 06/07/2018
    Power sanded (12x18 vibrating) older PTP deck with SW acrylic semi-trans stain. Most came up with 36 followed with 60 grit paper but there are still spots that didn't. I'm afraid of these becoming ugly shiny blotches when following with RAD stain, so will the RAD stripper remove these spots without blotching surrounding wood that is "clean"? Spot sanding is another option but as I still need to strip verticals I thought I spot treating with the stripper may work without taking more material off as long as it won't create problems with the surrounding "clean" wood. Will brighten everything with RAD brightener once verticals are stripped.
    • We will reply to your comment shortly
      RAD Products · 06/07/2018
      Might be best to just sand them off so it is evenly sanded when done.
      • We will reply to your comment shortly
        Alan Ulbrich · 06/08/2018
        I would agree...but my 60 year old back & knees might take a little more convincing! 600sf PTP deck is 20 years old, so this is probably the last restoration before I replace. Can you tell me if stripper will affect surrounding “clean” wood in a negative way? I’m not so worried about getting everything even as old PTP is far from even at this point. Photo attached.
        • We will reply to your comment shortly
          RAD Products · 06/08/2018
          No issues but best to strip and brighten all the wood.
  • We will reply to your comment shortly
    Cory · 06/03/2018
    Will this remove Rustoleum deck restore from a deck?
    • We will reply to your comment shortly
      RAD Products · 06/03/2018
      Sorry, but no. The only way to remove this product is to sand it off.
  • We will reply to your comment shortly
    Jason R · 05/30/2018
    Will this strip off Thompson's Water Seal?
    • We will reply to your comment shortly
      RAD Products · 05/30/2018
      Yes it will.
      • We will reply to your comment shortly
        Jason R · 05/31/2018
        Yipee, just ordered then. That Thompson paraffin coating is hellish and looks black and nasty after only a year.