RAD CLEANERdefaultRestore A Deck Cleaner Instructions and How To Tips

Keeping your wooden deck in good condition is without a doubt crucial to both its appearance and lifespan. Nothing looks worse and deteriorates more quickly than a neglected deck. Many deck owners have opted to do their own deck maintenance.

Restore A Deck cleaner is a specifically designed two-part system that is best used to clean and prep a wood deck prior to resealing it. The Restore A Deck cleaner system consists of a wood cleaner that will remove dirt, grime, mold, mildew, and grayed wood fibers. Step 2 of RAD Cleaner is a wood brightener that corrects the pH of the wood and brightens it up prior to applying a wood stain or sealer.

To clean a deck using the Restore A Deck system follow these easy step-by-step instructions.

1. Be sure air temperatures or between 45-90 degrees. Remove all furnishings from the deck and the surrounding area.

2. Though Restore A Deck is Eco-Friendly it is still a good idea to cover sensitive plants and shrubbery or pre-wet them with fresh water. Use plastic to cover doors and windows in the surrounding area.

3. Follow the Restore A Deck instructions to mix the Step 1 Cleaner in a clean bucket until all crystals are dissolved and transfer to sprayer to avoid clogging of sprayer inlet tube.

4. Lightly spray the wood deck with water. Use a pump sprayer or scrub brush to apply RAD Cleaner to the wood. Allow the cleaner to dwell for 5-15 minutes. Keep the deck wet by misting with water during the dwell time. If using a pump sprayer please make sure that no undissolved powder is poured into the sprayer. It will get clogged!

5. Hand scrub or use a pressure wash to remove dirt, grime, and graying from the wood surface. Do not use excessive pressure. Pressure washing at 1500 PSI is much more effective and easier.

6. Once cleaned, rinse the wood deck and the surrounding plants, windows, house siding, etc.

7. While the deck is still wet from rinsing, apply the Restore A Deck Wood Brightener (Step 2).

8. Blend the RAD Wood Brightener by following the product’s instructions and apply with a pump sprayer. Allow the brightener to dwell for 10 minutes then rinse off. No need to having scrub or pressure wash the RAD Brightener. Make sure to rinse the RAD Brightener thoroughly for 20 minutes until all soap suds are removed after the 10 minutes dwell time.

Note that the RAD cleaner is not intended for removing old deck stains or sealers. Please see Restore A Deck Stain Stripper when dealing with existing stains.

If you have any specific questions about your project or just need some help, please ask below!

Ask a Question or Post a Picture...
You are guest ( Sign Up ? )
or post as a guest
Loading comment... The comment will be refreshed after 00:00.
  • We will reply to your comment shortly
    John Barnhard · 07/23/2015
    I have a new deck that is made of cedar and it is 3 months old.
    It has an aluminum black railing on the deck will your product hurt the black paint on the aluminum or the aluminum?
    How soon can I use your product on this new deck?
    Do you have a deck brush I can oder with your product?
  • We will reply to your comment shortly
    RAD Products · 06/29/2015
    Steve M:
    Hello,

    I saw the previous post below with a similar topic but the deck was 2 years old and untreated, mine is brand new...

    I just finished installing my new tiger wood deck about 2 weeks ago and was prepping the surface for stain/uv oil with the 2-in-1 RAD system. It had just rained the night before and since the directions said to wet the deck first I applied the cleaner, scrubbed and throughly rinsed. About 20mins later I applied the brighter and throughly rinsed.

    Now, it appears that the deck had a white film/hue to it, what do I do? Can I simply apply the UV stain or should I do something else first?

    Thanks!

    Did you pressure wash off the deck cleaner? You may not have removed all the wood fibers from the wood.
  • We will reply to your comment shortly
    Steve M · 06/29/2015
    Hello,

    I saw the previous post below with a similar topic but the deck was 2 years old and untreated, mine is brand new...

    I just finished installing my new tiger wood deck about 2 weeks ago and was prepping the surface for stain/uv oil with the 2-in-1 RAD system. It had just rained the night before and since the directions said to wet the deck first I applied the cleaner, scrubbed and throughly rinsed. About 20mins later I applied the brighter and throughly rinsed.

    Now, it appears that the deck had a white film/hue to it, what do I do? Can I simply apply the UV stain or should I do something else first?

    Thanks!
  • We will reply to your comment shortly
    RAD Products · 06/28/2015
    Allan:
    How do I remove black circles on redwood caused by leaving a propane tank on the deck all year? Cleaner/brightener didn't work.

    Nothing probably will as that stain is deep in the wood grain. It is most likely rust and if anything would work, it would be the brightener.
  • We will reply to your comment shortly
    Allan · 06/27/2015
    How do I remove black circles on redwood caused by leaving a propane tank on the deck all year? Cleaner/brightener didn't work.
  • We will reply to your comment shortly
    RAD Products · 06/15/2015
    Bill Graf:
    My screen porch wall (siding) is stained but the floor and railings are not. Both have mold/mildew. Do I use the cleaner the same way on both surfaces? Do I need to use the brightener on the stained areas if they are not going to be restained?

    Use the cleaner on all. Only brighten where unstained.
  • We will reply to your comment shortly
    Bill Graf · 06/14/2015
    My screen porch wall (siding) is stained but the floor and railings are not. Both have mold/mildew. Do I use the cleaner the same way on both surfaces? Do I need to use the brightener on the stained areas if they are not going to be restained?
  • We will reply to your comment shortly
    RAD Products · 05/05/2015
    frank:
    Used Restore kit on 6 month old pressure treated pine and a few days later some strips of wood turned slightly green. Why did some wood turn green and is it ok to apply stain over the green. PS: it was not green before restore kit

    This is a result of your wood, not the cleaner or brightener. Not sure why but it is related to the wood. You can stain over it.
  • We will reply to your comment shortly
    frank · 05/05/2015
    Used Restore kit on 6 month old pressure treated pine and a few days later some strips of wood turned slightly green. Why did some wood turn green and is it ok to apply stain over the green. PS: it was not green before restore kit
  • We will reply to your comment shortly
    RAD Products · 10/27/2014
    Gary B:
    Will Restore-A-Deck Cleaner or Restore-A-Deck Brightener damage exterior iron or aluminum ballisters, or aluminum clad doors, or remove paint from siding?

    Does not harm paint but you shuld take precautions around aluminum with the Brightener. Either pre wet and rinse right away if any brightener get on the aluminum or take precautions by covering.
  • We will reply to your comment shortly
    Gary B · 10/25/2014
    Will Restore-A-Deck Cleaner or Restore-A-Deck Brightener damage exterior iron or aluminum ballisters, or aluminum clad doors, or remove paint from siding?
  • We will reply to your comment shortly
    RAD Products · 10/15/2014
    Jim T:
    We have a composite wood deck that a contractor spilled tub re-glazing paint on several planks. Although he scrubbed it twice with his own cleaner, there is visible white staining still evident. Is your stripper the proper product to use in this situation, particularly with a composite wood deck?

    Our composite wood deck is unusual in that it is NOT covered with an external plastic material, e.g., with a faux wood grain pattern. It is a smooth, flat wood product with very small plastic bits compressed into the material. (We inherited it with the house, and do not know the brand)

    Would love any expert input feedback you have about using the stripper in addition to the cleaner and brightener. Thanks!

    Sorry but our stripper does not remove paint and not sure if it will remove the haze left from the paint. Not sure what would work for this scenario.
  • We will reply to your comment shortly
    RAD Products · 10/15/2014
    Sue Vermillion:
    My husband mixed up some brightener a week ago to use on our deck and did not use it all up. I am now going to clean the porch. Can I use the brightener that was mixed a week ago?

    Yes you can use the brightener after mixing a week ago. Only the cleaner would have gone bad.
  • We will reply to your comment shortly
    Sue Vermillion · 10/15/2014
    My husband mixed up some brightener a week ago to use on our deck and did not use it all up. I am now going to clean the porch. Can I use the brightener that was mixed a week ago?
  • We will reply to your comment shortly
    Jim T · 10/15/2014
    We have a composite wood deck that a contractor spilled tub re-glazing paint on several planks. Although he scrubbed it twice with his own cleaner, there is visible white staining still evident. Is your stripper the proper product to use in this situation, particularly with a composite wood deck?

    Our composite wood deck is unusual in that it is NOT covered with an external plastic material, e.g., with a faux wood grain pattern. It is a smooth, flat wood product with very small plastic bits compressed into the material. (We inherited it with the house, and do not know the brand)

    Would love any expert input feedback you have about using the stripper in addition to the cleaner and brightener. Thanks!
  • We will reply to your comment shortly
    RAD Products · 09/28/2014
    Cheryl Morris:
    My redwood decks front & rear are 10 yrs old, previously I put an opaque redwood paint on it & it pealed and was a mess so when that wouldn't come off I had it sandblasted which damaged the wood and really exposed the grain it was as mess so we sanded it a bit and then put on a deck sealer treatment which had darkened the wood and now it's ugly & discolored and not grey but not pretty redwood color. I have started sanding the back deck it and it does look like redwood color again. Should I sand the whole thing then use your cleaner & brightener on it afterwords? Please advise before I make things worse. Thanks

    Use our Stripper and Brightener for the prep. It will remove the darkened stain without the need for heavy sanding.
  • We will reply to your comment shortly
    Cheryl Morris · 09/27/2014
    My redwood decks front & rear are 10 yrs old, previously I put an opaque redwood paint on it & it pealed and was a mess so when that wouldn't come off I had it sandblasted which damaged the wood and really exposed the grain it was as mess so we sanded it a bit and then put on a deck sealer treatment which had darkened the wood and now it's ugly & discolored and not grey but not pretty redwood color. I have started sanding the back deck it and it does look like redwood color again. Should I sand the whole thing then use your cleaner & brightener on it afterwords? Please advise before I make things worse. Thanks
  • We will reply to your comment shortly
    RAD Products · 09/24/2014
    Bob G:
    Can restore-a-deck products (cleaner, stripper and brightener) be used before applying a TWP 1500 stain?

    Yes they can be used for the prep prior to applying TWP.
  • We will reply to your comment shortly
    Bob G · 09/24/2014
    Can restore-a-deck products (cleaner, stripper and brightener) be used before applying a TWP 1500 stain?
  • We will reply to your comment shortly
    RAD Products · 09/07/2014
    urbanus04:
    I am working to clean a 3500 sq ft fence.

    How long does your product stay active after it is mixed with water?

    Can I simply mist with plain water to keep the area wet or do I need to keep reapplying the cleaner for the 15 - 20 min?

    You can mist with water to keep wet. it is active for 1-2 hours at most.
  • We will reply to your comment shortly
    Calvin Lowder · 09/06/2014
    I am working to clean a 3500 sq ft fence.

    How long does your product stay active after it is mixed with water?

    Can I simply mist with plain water to keep the area wet or do I need to keep reapplying the cleaner for the 15 - 20 min?
  • We will reply to your comment shortly
    RAD Products · 07/27/2014
    Van:
    I want to clean and brighten an ipe deck around our stucco house. Will your product cause "bleach" marks on the stucco if it comes in contact or do I need to protect the house from getting any of your product on it. If i wet the stucco first will that suffice? Love your site, lots of good info

    It will not bleach out the stucco but it will clean it. Best to pre wet and rinse right away any cleaner or brightener that gets on it.
  • We will reply to your comment shortly
    Van · 07/27/2014
    I want to clean and brighten an ipe deck around our stucco house. Will your product cause "bleach" marks on the stucco if it comes in contact or do I need to protect the house from getting any of your product on it. If i wet the stucco first will that suffice? Love your site, lots of good info
  • We will reply to your comment shortly
    RAD Products · 07/25/2014
    michelle kopp:
    I just finished using RAD cleaner on my 2 year old untreated cedar deck. I applied it with a sprayer and then used a brush to scrub. ( It was a lot of work to remove the gray and dirty areas .). After rinsing several times I and letting it dry slightly I noticed white or light gray film especially near the knots in the boards. It looks like wood fibers perhaps. If I scratch it with my nail it comes up. What happened? And is there anything I should do before I apply the brightner?

    When you let wood untreated for 2 years the top layer of wood cells will heavily oxidize. When you use the cleaner you are removing all of this. The wood is basically "shedding" a layer of damaged wood cells. The use of a pressure washer makes this much easier and you would have gotten more of it off. What you are seeing is that you did not get it all off from scrubbing. To remove th rest you should either lightly pressure wash or sand it off, then brighten.
  • We will reply to your comment shortly
    michelle kopp · 07/24/2014
    I just finished using RAD cleaner on my 2 year old untreated cedar deck. I applied it with a sprayer and then used a brush to scrub. ( It was a lot of work to remove the gray and dirty areas .). After rinsing several times I and letting it dry slightly I noticed white or light gray film especially near the knots in the boards. It looks like wood fibers perhaps. If I scratch it with my nail it comes up. What happened? And is there anything I should do before I apply the brightner?
  • We will reply to your comment shortly
    RAD Products · 07/13/2014
    Glen Sewell:
    Can I apply the cleaner and brightener after a rainfall? Or does the wood have to be completely dry?

    Yes you can do that.
  • We will reply to your comment shortly
    Glen Sewell · 07/13/2014
    Can I apply the cleaner and brightener after a rainfall? Or does the wood have to be completely dry?
  • We will reply to your comment shortly
    RAD Products · 07/12/2014
    Glen Sewell:
    Hello,
    I applied your deck cleaner and noticed the following:

    1. I did not see any bubbling or soapy film on the surface of the wood as per your website.

    2. After power washing i noticed that there is still white/greyish areas.

    Is the above normal with your product?

    thank you,
    Glen

    It is possible that you have an old clear sealer or stain that is preventing the cleaner from working correctly. If you do then you would need the RAD Stripper not the cleaner for prep. Brighten after as well.
  • We will reply to your comment shortly
    Glen Sewell · 07/11/2014
    Hello,
    I applied your deck cleaner and noticed the following:

    1. I did not see any bubbling or soapy film on the surface of the wood as per your website.

    2. After power washing i noticed that there is still white/greyish areas.

    Is the above normal with your product?

    thank you,
    Glen
  • We will reply to your comment shortly
    RAD Products · 06/27/2014
    David Standerfer:
    We have a redwood deck in good condition that we want to clean. Would you advise reducing the amount of cleaner (i.e., adjusting the strength down)? What about the brightener? Thank you.

    If not very dirty than yes you can reduce the cleaner concentration down to 2-4 oz per gallon of water. Brightener should stay at about 6 oz per gallon of water.