Do-It-Yourself Wood Restoration Made Simple!

Restore-a-deck.com

Deck Cleaning vs. Deck Stripping

by The Sealer Store

When to Use a Deck Stripper over a Cleaner

The benefits of regular wood deck maintenance are well worth the time and cost. Regularly cleaning and protecting your deck with a wood stain or sealer is one of the best things you can do to guarantee years of use.

The proper procedure for regular wood maintenance is to clean or prep the wood prior to applying a wood deck stain. The purpose of cleaning the wood it so the new deck stain will penetrate or adhere properly and perform as promised. To establish whether you will need to use RAD deck cleaner or RAD deck stripper you first have to determine what is on the wood surface that needs to be removed.

Deck Cleaners
Restore A Deck cleaners come in a powder form and contain sodium percarbonate along with other additives that boost the overall effectiveness dramatically. RAD deck cleaners will remove contaminants such as dirt, grime, graying, mold, mildew, algae, and mill glaze. They break down these unwanted soils making it easier to scrub or pressure wash the wood to a newly restored surface ready for stain.

RAD wood deck cleaners are designed to clean wood that is grayed and dirty and has little to no existing deck stain present. If you are unsure if your deck has old stain or sealer on it splash some water on the surface. If the water beads up there are some remnants of old sealer or stain, if it absorbs into the wood quickly there is little or no sealer.

Deck Stain Strippers
If it is obvious that a deck has an old failing stain or sealer on it, or if water beads up then it may be necessary to use a deck stain stripper as opposed to a deck cleaner. Restore-A-Deck strippers contain more aggressive caustics than deck cleaners. Unlike a cleaner, a wood stain stripper will emulsify and breakdown most water and oil based transparent, semi-transparent and semi-solid deck stains so they can be washed off more easily.

At the same time dirt, mold, mildew, and all other contaminants are also removed from the wood surface along with the failing deck stain. It isn’t necessary to use both a deck stripper and a deck cleaner during the same washing process. Determine what is on the surface of your wood deck and then decide whether you need a deck cleaner or stripper.

Note that once the wood is cleaned or stripped you need to follow up with an application of the Restore-A-Deck wood brightener. This restores the wood’s pH balance for better stain penetration and enhances the beauty of the wood. It is a necessary step after deck cleaning or stripping.

Subscribe
Notify of
guest
58 Comments
Newest
Oldest
Inline Feedbacks
View all comments
anne
anne
9 months ago

Do aI use a brush or sprayer to apply solid stain to an old deck? The deck had cabot oil stain bc I found the cans and they say deck stain. It is mostly worn off probably stained once in the 90’s, not rotted and water absorbs & doesn’t bead. You can however see some areas of old red stain. Should I strip it?
I have approx 400 sq feet. Do I need two gallons of stain and one pack of cleaner & brightener ( powder makes 5 gallons size)?
Thanks

RAD Products
Admin
9 months ago
Reply to  anne

Clean and brighten the wood, one kit. Apply the RAD Solid Stain with brushes and rollers. For 400 Sq feet and the two coats needed, you will need 3-4 gallons. More if you have railings and steps as well.

Susan
Susan
4 years ago

If I use stripper with additives to remove old Behr acrylic stain and it doesn’t work, do I sand and then use brightener?

RAD Products
Admin
4 years ago
Reply to  Susan

Yes but post a picture of the current condition.

Susan
Susan
4 years ago
Reply to  RAD Products

Here you go!

RAD Products
Admin
4 years ago
Reply to  Susan

Yes, correct. You will have to sand this coating off. Too thick to strip. Looks like a paint.

RAD Products
Admin
6 years ago

[quote name=”rick123″][quote name=”TheSealerStore”][quote name=”rick123″]We have new mahogany porch boards (about 6 mos. old), partially under cover and partially exposed to the sun and rain. The wood came with a protective “glaze” that initially repelled water but now has weathered off in some parts but not others, so the entire floor probably has to be stripped before stain/UV protection is applied. Would the Restore-A-Deck Stripper and Brightener “bleach” the color out of the wood?[/quote]
It will strip it and remove the gray oxidation.[/quote]
Thank you. Yes, I do want to strip off any of the coating that came on the boards before applying a protective stain to the entire porch. There is very little gray oxidation, since the porch is only a few months old. Can I be confident that the RAD Stripper plus Brightener will not remove the natural pigment in the mahogany boards, but will only prep the boards for stain? Thanks again.[/quote]
It does prep the wood for restaining. The natural wood pigment fades over time though and when you remove oxidized wood cells, you are basically removing a layer of wood so if the color of the wood is lighter after the prep, it is not due to the RAD products but the wood fading.

rick123
rick123
6 years ago

[quote name=”TheSealerStore”][quote name=”rick123″]We have new mahogany porch boards (about 6 mos. old), partially under cover and partially exposed to the sun and rain. The wood came with a protective “glaze” that initially repelled water but now has weathered off in some parts but not others, so the entire floor probably has to be stripped before stain/UV protection is applied. Would the Restore-A-Deck Stripper and Brightener “bleach” the color out of the wood?[/quote]
It will strip it and remove the gray oxidation.[/quote]
Thank you. Yes, I do want to strip off any of the coating that came on the boards before applying a protective stain to the entire porch. There is very little gray oxidation, since the porch is only a few months old. Can I be confident that the RAD Stripper plus Brightener will not remove the natural pigment in the mahogany boards, but will only prep the boards for stain? Thanks again.

RAD Products
Admin
6 years ago

[quote name=”rick123″]We have new mahogany porch boards (about 6 mos. old), partially under cover and partially exposed to the sun and rain. The wood came with a protective “glaze” that initially repelled water but now has weathered off in some parts but not others, so the entire floor probably has to be stripped before stain/UV protection is applied. Would the Restore-A-Deck Stripper and Brightener “bleach” the color out of the wood?[/quote]
It will strip it and remove the gray oxidation.

rick123
rick123
6 years ago

We have new mahogany porch boards (about 6 mos. old), partially under cover and partially exposed to the sun and rain. The wood came with a protective “glaze” that initially repelled water but now has weathered off in some parts but not others, so the entire floor probably has to be stripped before stain/UV protection is applied. Would the Restore-A-Deck Stripper and Brightener “bleach” the color out of the wood?

RAD Products
Admin
7 years ago

[quote name=”guitargerber”]I used the cleaner and the brightener. Then, the weather turned cold, then wet, then cold, then wet again. It will have been 3 weeks since I brightened the deck – can I still use the Armstrong Clark transparent stain? Do I need to re-brighten first?[/quote]
You should rebrighten since it has been 3 weeks since the prep was done.

Avatar photo
7 years ago

I used the cleaner and the brightener. Then, the weather turned cold, then wet, then cold, then wet again. It will have been 3 weeks since I brightened the deck – can I still use the Armstrong Clark transparent stain? Do I need to re-brighten first?

RAD Products
Admin
7 years ago

[quote name=”jcanfield13″]If you don’t recommend your products for regular clean – only prep, do you have a product that you do recommend for regular maintenance cleaning?[/quote]
We do not. You want something that is not too aggressive to the point that it will remove the coating.

Avatar photo
7 years ago

If you don’t recommend your products for regular clean – only prep, do you have a product that you do recommend for regular maintenance cleaning?

RAD Products
Admin
7 years ago

[quote name=”jcanfield13″]I used RAD step 1 and 2 last year on my newly constructed pressure treated wood deck. I then stained with an Armstrong Clark semitransparent stain. This spring, I would like to clean the deck as there are some stains on it. Do I still use both step 1 and 2, or just step 1? Will the brightener hurt my existing stain?[/quote]
Our cleaning products are prepping products for retaining. I would not suggest using them for just cleaning unless you want to reapply the AC. They will remove some of the stain.

Avatar photo
7 years ago

I used RAD step 1 and 2 last year on my newly constructed pressure treated wood deck. I then stained with an Armstrong Clark semitransparent stain. This spring, I would like to clean the deck as there are some stains on it. Do I still use both step 1 and 2, or just step 1? Will the brightener hurt my existing stain?

RAD Products
Admin
8 years ago

[quote name=”Annette Grant”]I have cleaned my deck with a pressure cleaner and it has left trail marks when I sprayed close to the deck and they are obvious. Could you please advise me of what do I do with this problem before I apply stain. I have scrubbed using deck cleaner with a scrubbing brush.
Thank you[/quote]
You cannot fix the pressure washing marks with a cleaner, brightener or stain stripper. You would have to sand the entire floor “evenly” to remove them. Use 60 grit paper. After you should use the RAD kits for the final prep before staining.

Annette Grant
Annette Grant
8 years ago

I have cleaned my deck with a pressure cleaner and it has left trail marks when I sprayed close to the deck and they are obvious. Could you please advise me of what do I do with this problem before I apply stain. I have scrubbed using deck cleaner with a scrubbing brush.
Thank you

RAD Products
Admin
8 years ago

[quote name=”Larry Joe”]It appears that RAD Stripper is not suitable for stripping solid oil-based stain from my (pressure treated pine) deck. The stain in some parts of the deck surface is mostly gone (appears black from dirt, mold, mildew) while other deck sections are just faded solid stain (and mold/mildew). What product is recommended?[/quote]
No deck stain stripper will remove a solid stain easily or effectively.

Larry Joe
Larry Joe
8 years ago

It appears that RAD Stripper is not suitable for stripping solid oil-based stain from my (pressure treated pine) deck. The stain in some parts of the deck surface is mostly gone (appears black from dirt, mold, mildew) while other deck sections are just faded solid stain (and mold/mildew). What product is recommended?

RAD Products
Admin
8 years ago

[quote name=”Connie Reimer”]I will be using Armstrong semi-transparent oil based stain. Currently the desk has a semi-transparent stain. The deck is in good condition. It does have green/mold spots and sections where there is very little or no stain left. Will I just need to use Deck Stain Stripper?[/quote]
That and the wood brightener to neutralize after.

Connie Reimer
Connie Reimer
8 years ago

I will be using Armstrong semi-transparent oil based stain. Currently the desk has a semi-transparent stain. The deck is in good condition. It does have green/mold spots and sections where there is very little or no stain left. Will I just need to use Deck Stain Stripper?

RAD Products
Admin
8 years ago

[quote name=”Shelley Juergens”]Around the wood screws there is a dark bleeding on the cedar wood, Step 2 was applied about less than 5 days ago I am planning to reapply step 2 you can see different shades in the cedar. restoring the deck I can only work on it for about 3 hours physically. is there something different i should know about for the bleeding around the wood screws?[/quote]
The is rust from your screws. The brightener may remove the black rust stains but it will come back once rain rusts your screws again.

Shelley Juergens
Shelley Juergens
8 years ago

Around the wood screws there is a dark bleeding on the cedar wood, Step 2 was applied about less than 5 days ago I am planning to reapply step 2 you can see different shades in the cedar. restoring the deck I can only work on it for about 3 hours physically. is there something different i should know about for the bleeding around the wood screws?

RAD Products
Admin
8 years ago

[quote name=”koppernickel”]i have a 16 year old yellow pine wrap around mostly covered deck/porch with one on the west and north side of the house and one on the south side of the house. The west and north gets both hot sun and shade. I have cleaned and stained it 4-5 times with Olympus maximum semi transparent natural redwood over the years and it is now blotchy where it won’t accept stain to the bare areas. I figure I need to strip, brighten, and restain it. Will restore a deck strip acrylic/oil based stain like the Olympus? Which stain do you recommend for refinishing in my situation? The south deck is mostly shaded. I have a little prob with mildew but not bad. 7 foot deep. 39 foot northside and 26 foot west side. 29×8 on south side. Thank you for any assistance you can give[/quote]
The RAD does strip of oil based semi-transparent stain but it may have an issue when trying to remove 4-5 layers that have been over applied through the years. You may need to strip a few times to get it all off and even sand some stubborn areas. Once removed you need to use the RAD brightener for the final prep. Either the 100 or 1500 Series.

Avatar photo
8 years ago

i have a 16 year old yellow pine wrap around mostly covered deck/porch with one on the west and north side of the house and one on the south side of the house. The west and north gets both hot sun and shade. I have cleaned and stained it 4-5 times with Olympus maximum semi transparent natural redwood over the years and it is now blotchy where it won’t accept stain to the bare areas. I figure I need to strip, brighten, and restain it. Will restore a deck strip acrylic/oil based stain like the Olympus? Which stain do you recommend for refinishing in my situation? The south deck is mostly shaded. I have a little prob with mildew but not bad. 7 foot deep. 39 foot northside and 26 foot west side. 29×8 on south side. Thank you for any assistance you can give

RAD Products
Admin
8 years ago

[quote name=”John Meinken”]Hi, Stripping my deck and Gazebo is going to be a multi-day project. Can I strip it entirely then go back later, re-wet and then use the brightener?
Regards,
John[/quote]
You can but it is always best to brighten as soon as possible.

John Meinken
John Meinken
8 years ago

Hi, Stripping my deck and Gazebo is going to be a multi-day project. Can I strip it entirely then go back later, re-wet and then use the brightener?
Regards,
John

RAD Products
Admin
8 years ago

[quote name=”Rick Jensen”]I have a new Brazilian Redwood deck that was treated initially with a SSW Deckscapes stain. A matter of weeks later the surface looked gray and terrible. I’ve power washed the deck, but it hasn’t made much of an impact, if any. I tried treating a small area with the RAD cleaner/brightener and it doesn’t appear to have had any impact so I’m considering using a stripper/brightener, but I don’t want to ruin the wood with harsh chemicals before putting on TWP. Is there a better path, such as just letting it weather for several months, or trying different methods?[/quote]
Seems your options are either strip and brighten or sand it all off. It does not just weather away.

Rick Jensen
Rick Jensen
8 years ago

I have a new Brazilian Redwood deck that was treated initially with a SSW Deckscapes stain. A matter of weeks later the surface looked gray and terrible. I’ve power washed the deck, but it hasn’t made much of an impact, if any. I tried treating a small area with the RAD cleaner/brightener and it doesn’t appear to have had any impact so I’m considering using a stripper/brightener, but I don’t want to ruin the wood with harsh chemicals before putting on TWP. Is there a better path, such as just letting it weather for several months, or trying different methods?

Todd
Todd
8 years ago

I used BM arborteck last year on a brand new pt deck . Black mold
Is on top and underneath . Faded only repelled water
For two months . Now I have to sand and stripp. Going back with twp. Hope this is better.

RAD Products
Admin
9 years ago

[quote name=”kyle brauner”]I accidently ordered the cleaner and brightener kit. I needed the stripper and brightner. How do I go about returning the cleaner for a refund? The cleaner has not been opened.[/quote]
Kyle, you would have to return the whole kit as the stripper does not come in a kit. You cannot just exchange the cleaner of a stripper. Please call to discuss.

kyle brauner
kyle brauner
9 years ago

I accidently ordered the cleaner and brightener kit. I needed the stripper and brightner. How do I go about returning the cleaner for a refund? The cleaner has not been opened.

RAD Products
Admin
9 years ago

[quote name=”jmdllski”]We first power washed the deck which removed most of the deck stain on the surface however there is still quite a bit that needs to be removed from the sides. This is not a typical deck with post and spindles, This is a low deck with 2 steps. the sides are actually benches and there is decorative wood holding the benches. There are alot of crevices and angles that need to be stripped. After power washing, we got a sander (hand) using a 60 grit paper,This didn’t remove anything. We haven’t tried the belt sander but i’m concerned that it won’t remove it either. Any other suggestions? I’ve been reading about strippers but I see there are mixed reviews. We want to put a semi stain on the deck.[/quote]
Out stripper will not remove a solid stain. It may help some but it will not get it all off.

jmdllski
jmdllski
9 years ago

We first power washed the deck which removed most of the deck stain on the surface however there is still quite a bit that needs to be removed from the sides. This is not a typical deck with post and spindles, This is a low deck with 2 steps. the sides are actually benches and there is decorative wood holding the benches. There are alot of crevices and angles that need to be stripped. After power washing, we got a sander (hand) using a 60 grit paper,This didn’t remove anything. We haven’t tried the belt sander but i’m concerned that it won’t remove it either. Any other suggestions? I’ve been reading about strippers but I see there are mixed reviews. We want to put a semi stain on the deck.

RAD Products
Admin
9 years ago

[quote name=”jimmer”]My deck has paint on it that has peeled in many spots and I want to completely remove the paint. Will the RAD stripper work or do I need a different product?[/quote]
No deck stripper will remove paint. You will need to sand it off.

jimmer
jimmer
9 years ago

My deck has paint on it that has peeled in many spots and I want to completely remove the paint. Will the RAD stripper work or do I need a different product?

RAD Products
Admin
9 years ago

[quote name=”Dealer”]Have 15year old pressure treated deck with deteriorated Sikkens stain on 50 percent of it. Have to restore it w/out useing Sikkens again. Should I strip it, brighten it or just clean it &brighteni it?what do u think if I use TWP cedar tone stain. Please give me some advice – I need it. Won’t hold u responsible for it.Thanks, Bill.[/quote]
Strip and brighten for the Sikkens removal. Yes the TWP would be a good choice after removal.

Avatar photo
9 years ago

Have 15year old pressure treated deck with deteriorated Sikkens stain on 50 percent of it. Have to restore it w/out useing Sikkens again. Should I strip it, brighten it or just clean it &brighteni it?what do u think if I use TWP cedar tone stain. Please give me some advice – I need it. Won’t hold u responsible for it.Thanks, Bill.

RAD Products
Admin
10 years ago

75 is ideal weather. It will work between 50 and 95 degrees with no issues.

Cameron Brister
Cameron Brister
10 years ago

Can I use RAD blue step 2 in weather cooler than 75 degrees? The instructions look pretty clear that 3 days of sunny, 75 degree weather is important. That probably won’t happen where I live. Does that mean I can only use RAD red step one?

RAD Products
Admin
10 years ago

Adam, try scoring the areas first with sanding so the stripper will be able to get through the stain and soften the bond.

Adam
Adam
10 years ago

I just used RAD stripper with power washing to remove old Sikkens SRD semi transparent stain on my mahogany deck. It seemed to work great in some spots, with the old stain coming right off. The trouble is, in other places there seemed to be either embedded stain or mold stains that would not come off without very direct power washing which I don’t really want to do (to not damage the wood). tried a second application without success. I’m not really sure what else to do about this. My guess is it is more of an issue to do with how the deck was stained last time (prior owner), but otherwise the product worked well.

RAD Products
Admin
10 years ago

The Restore A Deck Stain Stripper does remove Sikkens SRD in the oil based formula. We do not have dealers in Canada.

Jon
Jon
10 years ago

I want to reapply a Sikkens SRD stain which was an oil based product 5 years ago. Last year they changed the formula so it now the SRD is a “hybrid” product- part oil and part water base. Sikkens say you must remove the old stain completely before applying the new product. Will your product do the job? Secondly where is your nearest dealer to Vancover BC Canada?

RAD Products
Admin
10 years ago

I would just strip and rinse the ground when done. never had any say there was an issue with their dogs.

Bill F
Bill F
10 years ago

Hi, our dog is always sniffing around under our deck. If we use your wood stripper product, doesn’t the old (oil based) stain wash off onto the ground where it could sit and get picked up by our dog’s feet? We were going to lay down plastic drop cloths but they won’t stand up to all of the water generated by pressure-washing the stain/stripper off because there will be a lot of runoff. Any suggestions?

RAD Products
Admin
10 years ago

I would use the cleaner on the floor. Durastain is a semi-solid and is fairly difficult to remove. You may need to strip more the once.

Avatar photo
10 years ago

The stain on the surface of my redwood deck floor is completely weathered away. However, the rail spindles have a fair amount of residual Wolmans durastain. I plan to apply RAD stripper to the spindles. Should I go ahead and use the stripper on the deck floor as well or use the cleaner on the floor? Thanks

Kathryn
Kathryn
10 years ago

THANKS VERY MUCH! 😉

RAD Products
Admin
10 years ago

TWP wants you to wait 48 hours after prepping.

Kathryn
Kathryn
10 years ago

We will be working with limited time, and will be stripping and brightening with RAD. Redwood deck is pretty dry, and weather will be in the low 90’s with wind. Can we get by with 24hrs dry time before applying TWP100? How do you tell the wood is dry enough to apply the stain? We don’t want to waste our time and materials, but we don’t really have 3 days to wait between stipping and staining. Thanks!

RAD Products
Admin
10 years ago

You can wait a week to stain.

Avatar photo
10 years ago

I just completed stripping the deck. After I brighten it…….how soon does it need to be stained? I know it needs to dry thoroughly……but can I wait a week or so to stain?
Thanks

58
0
Would love your thoughts, please comment.x